background image

Ruijie RG-NBS5100 Series Switches Hardware Installation and Reference Guide 

 

Preparation before Installation 

 

13 

 

 

High or low extreme temperatures or low air pressure at high altitude that the battery can be subjected to during 

use, storage or transportation. 

 

Leaving the battery in an extremely high temperature and/or low air pressure surrounding environment that can 

result in an explosion or the leakage of flammable liquid or gas. 

2.2  Installation Site Requirements 

To ensure the normal working and a prolonged durable life of the equipment, the installation site must meet the 

following requirements. 

2.2.1  Ventilation 

For the RG-NBS5100 series, a sufficient space (at least 10 cm distances from both sides and the back plane of the 

cabinet) should be reserved at the ventilation openings to ensure the normal ventilation. After various cables have been 

connected, they should be arranged into bundles or placed on the cabling rack to avoid blocking the air inlets. It is 

recommended to clean the switch at regular intervals (like once every 3 months). Especially, avoid dust from blocking 

the screen mesh on the back of the cabinet. 

2.2.2  Temperature and Humidity 

To  ensure  the  normal  operation  and  prolong  the  service  life  of  RG-NBS5100  series  switch,  you  should  keep  proper 

temperature and humidity in the equipment room. 

If the equipment room has temperature and humidity that do not meet the requirements for a long time, the equipment 

may be damaged. 

 

In  an  environment  with  high  relative  humidity,  the  insulating  material  may  have  bad  insulation  or  even  leak 

electricity. Sometimes the materials may suffer from mechanical performance change and metallic parts may get 

rusted. 

 

In  an  environment  with  low  relative  humidity,  however,  the  insulating  strip  may  dry  and  shrink.  Static  electricity 

may occur easily and endanger the circuit on the equipment. 

 

In an environment with high temperature, the equipment is subject to even greater harm, as its performance may 

degrade significantly and various hardware faults may occur.   

Therefore,  the  ambient  temperature  and  humidity  of  the  RG-NBS5100  series  must  meet  the  requirements  listed  in 

Table 2-1: 

Table 2-1 Temperature and Humidity Requirements of the RG-NBS5100 Series Switch 

Temperature 

Relative Humidity 

0 ºC to 50ºC 

10% to 90% 

 

 

The requirements for the sampling site of the temperature and humidity in the operating environment of the device 

are as follows: 

There is no protective plate at the front or back of the equipment rack. 

The vertical height is 1.5 m above the floor. 

The distance from the front panel of the equipment is 0.4 m. 

Содержание RG-NBS5100 Series








































Отзывы: