Ruijie Reyee RG-ES106D-P Скачать руководство пользователя страница 61

Страница: 61 / 83

Hardware Installation and Reference Guide

Installing the Switch

seams no more than 1.5 cm (0.59 in.) in diameter to prevent rodents and other small animals from entering

the cabinet.

⚫

Antistatic wrist straps should be provided in the cabinet.

Simple Installation Steps for Cabinet

(1) Plan the available space before installing the cabinet. Reserve sufficient space for the front and rear doors

for maintenance.

(2) Install and fasten the cabinet in the designed position as planned.

(3) Install the appropriate cable troughs and cables.

(4) Install the tray and cable management brackets on the cabinet according to the number of switches installed

inside the cabinet.

Preparing

Before mounting an RG-ES1 switch into a cabinet, verify that the front and rear brackets of the cabinet are in

the right positions. If the brackets are too far forward, the front door of the switch may be too close to the front

door of the cabinet. As a result, the front door of the cabinet cannot be closed when the switch is connected

with network cables and fibers. Maintain a minimum clearance of 10 cm (3.94 in.) between the front panel of the

switch and the front door of the cabinet. Before mounting the switch into a cabinet, ensure that the following

conditions are met:

⚫

The cabinet is fixed.

⚫

All the internal units have been installed properly in the cabinet.

⚫

No obstacles to installation exist inside or around the cabinet.

⚫

The switch is prepared and moved to a place near the cabinet where you can handle it easily.

Installation Steps

(1) Attach the mounting brackets to the switch with the supplied screws, as shown in Figure 3-1.

Figure 3-1

Attaching the Mounting Bracket to RG-ES126S-LP/RG-ES118S-LP/RG-ES118GS-P

Содержание Reyee RG-ES106D-P



















































































Результаты поиска

Содержание Reyee RG-ES106D-P

Отзывы:

Похожие инструкции для Reyee RG-ES106D-P

Бренды по названию

Популярные бренды

Ruijie Reyee RG-ES106D-P, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание Reyee RG-ES106D-P

Отзывы:

Похожие инструкции для Reyee RG-ES106D-P

Бренды по названию

Популярные бренды