Ruijie Reyee RG-ES106D-P Скачать руководство пользователя страница 56

Страница: 56 / 83

Hardware Installation and Reference Guide

Preparing for Installation

Note

Please adopt protection grounding connections in buildings so that the switch can be connected to the

protection ground.

⚫

Lightning Grounding

The lightning protection system of facilities is standalone, and is composed of a lightning rod, a lower

conductor, and a connector connected to the grounding system. The grounding system is usually used for

power reference grounding and safety grounding of the cabinet. Lightning grounding is required only for

facilities and is not required for the switch.

⚫

EMC Grounding

Grounding required for electromagnetic compatibility includes shielded grounding, filter grounding, noise

and interference suppression, and level reference, which contribute to the overall grounding requirements.

The grounding resistance should be smaller than 1 ohm, and the ground terminals of the cabinet should be

grounded before the running of the switch.

2.2.7

Anti-interference Requirements

⚫

Take interference prevention measures for the power supply system.

⚫

Keep the switch away from the grounding equipment or lightning and grounding equipment of the power

device as much as possible.

⚫

Keep the switch far away from high-frequency current devices such as high-power radio transmitting station

and radar launcher.

⚫

Take electromagnetic shielding measures when necessary.

2.2.8

Lightning Protection Requirements

The RG-ES1 series switches can guard against lightning strikes. As an electric device, it may still be damaged

by strong lightning strikes. Take the following lightning protection measures:

⚫

Ensure that the ground cable of the cabinet is in good contact with the ground.

⚫

Ensure that the neutral point of the AC power socket is in good contact with the ground.

⚫

It is recommended to install a power lightning arrester in front of the power input end to enhance the

lightning prevention for the power supply.

⚫

When the AC power cable is imported outdoors and directly connected to the power port of the RG-ES1

series switches, lightning line bank should be adopted to prevent the switch from being hit by lightning

shocks. Usage of the lightning line bank: Connect the mains supply AC cable to the lightning line bank. Then,

connect the switch to the lightning line bank. This can help to prevent the current of high-voltage lightning

from passing the switch directly through the mains supply cable to a certain extent.

2.2.9

Inspection of the Installation Unit

Regardless of whether the switch is installed inside a cabinet or on a workbench, the following conditions must

be met:

⚫

The switch is equipped with fans. Therefore, maintain a minimum clearance of 15 cm (5.91 in.) around the

air vents for heat dissipation. It is recommended to install the switch inside a standard 19-inch cabinet. The

Содержание Reyee RG-ES106D-P



















































































Результаты поиска

Содержание Reyee RG-ES106D-P

Отзывы:

Похожие инструкции для Reyee RG-ES106D-P

Бренды по названию

Популярные бренды

Ruijie Reyee RG-ES106D-P, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание Reyee RG-ES106D-P

Отзывы:

Похожие инструкции для Reyee RG-ES106D-P

Бренды по названию

Популярные бренды