Copyright © 2016 Ruckus Wireless, Inc.
Page 1 of 4
Published September 2016, Part Number 800-71078-001 Rev B
Unleashed
TM
R310 Access Point
Quick Setup Guide
This
Quick Setup Guide
provides step-by-step instructions on how to set up
your Ruckus Wireless Unleashed R310 access point.
After completing the
steps described in this Guide, the Unleashed Master Access Point
(Master AP) will be created. Additional Unleashed access points can be
added to the network for additional coverage and capacity
.
B
EFORE
Y
OU
B
EGIN
Before deploying your Ruckus Wireless device, please check the Ruckus
Wireless Web site for the latest software and release documentation.
•
User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents
•
Product Limited Warranty documents are available at
http://support.ruckuswireless.com/warranty
•
Online Training Resources are available at
https://training.ruckuswireless.com
P
ACKAGE
C
ONTENTS
•
One Unleashed R310 access point
•
Two mounting screws and plastic wall anchors
•
One T8 5mm M2.5 Torx locking security screw
•
One unit removal pin
•
Regulatory flyer
•
Product warranty statement
•
Declaration of conformity, if required
•
This
Quick Setup Guide
C
ONFIGURING
THE
AP
•
Step 1: Collecting Setup Requirements, Hardware, and Tools
•
Step 2: Connect the AP to Power and Your Computer Network
•
Step 3: Log In and Run the Setup Wizard
•
Step 4: Customize Your Wireless LANs
•
Step 5: Deploy Additional Unleashed Access Points
Figure 1. Unleashed R310 AP - top view
Step 1: Collecting Setup Requirements, Hardware,
and Tools
•
A computer with Ethernet adapter running Windows 7 or equivalent,
with Firefox or equivalent web browser.
•
One Cat 5e (or better) Ethernet cable.
•
T8 Torx screwdriver.
•
An AC-to-12VDC power adapter (sold separately)
--OR--
an 802.3af-compliant Power over Ethernet (PoE) switch or PoE
injector.
Step 2: Connect the AP to Power and Your
Computer Network
A
After removing your Unleashed AP from its package, connect it to your
network switch or router using an Ethernet cable.
B
Connect the AC power adapter (sold separately) to the
12VDC
AP
port, and plug the AC power adapter into a convenient and protected
AC power source.
•
Alternatively, connect the
POE IN
port to a PoE injector or PoE
switch for both power and network connectivity.
Figure 2. AP rear panel
C
After bootup, verify that the
PWR
LED on the AP is a steady green.
Step 3: Log In and Run the Setup Wizard
A
As soon as the Unleashed AP is powered on and connected to the local
network, it boots up and begins broadcasting a temporary unencrypted
WLAN named “Configure.Me-[xxxxxx]” from the 2.4 GHz radio only.
B
Using your client’s WiFi configuration settings, select and associate to
the “Configure.Me-[xxxxxx]” WLAN.
Figure 3. Connect to the “ConfigureMe” WLAN
\
C
Launch a web browser and enter the following into the browser’s URL
bar:
unleashed.ruckuswireless.com
, and press
Enter
.
D
Select
Create New Unleashed Network
, and click
Start
to
begin.
Figure 4. Select “Create New Unleashed Network”
E
The “Configuring Unleashed Master” progress screen displays the
progress. Wait until the initialization process completes.
.
F
Once initialization is complete, ensure that you are still connected to
the “Configure.Me” WLAN, and click
Next
.
G
You will be redirected to the Setup Wizard. Complete the steps in the
Setup Wizard and click
Finish
.
Note:
Do NOT disconnect the power or network cable from the
device during the setup process.