Copyright © 2016 Ruckus Wireless, Inc.
Published March 2016, Part Number 800-71212-001 Rev A
Page 1 of 4
T710s Access Point
Quick Setup Guide
This
Mounting Guide
provides step-by-step instructions on how to
field-install the Ruckus Wireless T710s access point (AP).
For detailed information on planning the installation, performing a site
survey, and operating the T710s, refer to the
ZoneFlex Outdoor
Access Point User Guide
, available at
https://
support.ruckuswireless.com
.
WARNING:
Only trained and qualified personnel should be allowed to
install, replace, or service this equipment.
WARNING:
Installation of this equipment must comply with local and
national electrical codes.
CAUTION:
Make sure that you form a 80mm - 130mm (3”-5”) drip
loop in any cable that is attached to the AP or the building. This will
prevent water from running along the cable and entering the AP or the
building where the cable terminates.
CAUTION:
Be sure that grounding is available and that it meets local
and national electrical codes. For additional lightning protection, use
lightning rods and lightning arrestors.
CAUTION:
Make sure that proper lightning surge protection
precautions are taken according to local electrical code.
WARNING:
Ruckus Wireless strongly recommends that you wear eye
protection before mounting the T710s.
T
HIS
G
UIDE
IN
O
THER
L
ANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com
.
Vous trouverez la version française de ce guide à l'adresse suivante
https://support.ruckuswireless.com
.
こ の ガ イ ド の⽇本語版は
https://support.ruckuswireless.com
で ご覧 く だ さ い。
이
가이드의
한국어
버전은
웹
사이트
(
https://support.ruckuswireless.com
)
에서
확인하시기
바랍니다
.
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com.
B
EFORE
Y
OU
B
EGIN
Before deploying your Ruckus Wireless T710s, verify that all items
listed in
are included in the package. If any item is
damaged or missing, notify your authorized Ruckus Wireless sales
representative. Also, make sure that you have the required hardware
and tools.
R
EQUIRED
H
ARDWARE
AND
T
OOLS
•
Customer-supplied outdoor-rated three-wire (1-2mm
2
or 14-
18AWG) AC cable
•
1/2” (13mm) flat-blade screwdriver or equivalent
•
No. 2 Phillips screwdriver
•
Small flat-blade screwdriver
•
Torque wrench or torque screwdriver with sockets
•
Long-nose pliers
•
Electrical wire stripping and terminal crimping pliers
•
Pipe or pole --OR-- a sturdy flat surface
•
Electric drill with drill bits and customer-supplied wall anchors, flat
washers, and hex nuts for flat-surface mount
•
Four factory-supplied 1/2” (12.7mm) wide stainless steel
adjustable clamps, 2.5” (63.5mm) diameter, for main mounting
bracket on smaller poles
•
Ruler
P
ACKAGE
C
ONTENTS
A complete T710s field installation package includes all of the items
listed below (see Figure 1for illustrations):
•
T710s Access Point (A)
•
M25 data cable gland extender (B)
•
Three M25 data cable glands (C)
•
Outdoor AP Mounting Bracket (D)
•
AC Power Cable End Connector (E)
•
Cable Gland Extender Flat Gasket (F)
•
Safety cable kit (G)
•
One ground wire with lug (H)
•
Service Level Agreement/Limited Warranty Statement
•
Regulatory Statement
•
Ruckus Wireless AP Getting Started Guide
•
Declaration of Conformity
•
This
Quick Setup Guide
Figure 1:
Package Contents
S
TEP
1: C
ONNECTING
AND
S
EALING
THE
RJ-45
C
ABLES
The T710s may use zero, or one or two RJ-45 cables, one for
Ethernet when configured as a Root AP (RAP), and another when the
T710s is supplying PoE out to a peripheral device, such as a small cell
or micro cell radio. When the T710s uses RJ-45 cables, connect and
seal the cables using the M25 data cable glands as shown in Figure 3.
WARNING:
Do not use any PoE injector not tested and approved by
Ruckus Wireless to power the T710s Access Point.
WARNING:
Do not plug PoE IN power into the PoE OUT port. See
Figure 2:
PoE IN and PoE OUT ports
1
Feed the end of the cable through the sealing nut, rubber O-ring,
clamping ring assembly and cable gland base as shown in Figure
3.
CAUTION!
The minimum software revision for the T710s
is ZoneFlex (ZF) 9.13 or later, or SmartZone (SZ) 3.4 or
later.
DO NOT CONNECT THE T710s TO A RUCKUS
WIRELESS ZONEDIRECTOR RUNNING 9.12.2 OR
EARLIER.
