manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 98

TABLE 25 Ethernet port status LED in default mode

LED color

Status of the hardware

Recommended action

Off

A link is not established with the remote port.

•

Verify that the connection to the other network
device has been properly made. Also, make
certain that the other network device is
powered on and operating correctly.

•

Be sure the cable is plugged into both the
device and the corresponding device.

•

Verify that the proper cable type is used and its
length does not exceed specified limits.

•

Check the adapter on the attached device and
cable connections for possible defects.
Replace the defective adapter or cable if
necessary.

•

Verify that the port has not been disabled
through a configuration change. You can use
the CLI. If you have configured an IP address
on the device, you also can use the Web
management interface or Brocade Network
Advisor.

•

If the other actions do not resolve the problem,
try using a different port or a different cable.

Steady green

The port has established a valid link at 1000 Mbps.

None.

Flashing green

The port has established a valid link at 1000 Mbps. Flashing indicates
the port is transmitting and receiving user packets.

None.

Steady amber

The port has established a valid link at 10 or 100 Mbps.

None.

Flashing amber

The port has established a valid link at 10 or 100 Mbps. Flashing
indicates the port is transmitting and receiving user packets.

None.

Interpreting nonport-side LEDs

There are no LEDs found on the nonport-side view of the Ruckus ICX 7150 devices.

Pinging an IP address

To verify that a device can reach another device through the network, enter a command similar to the following at any level of the CLI.

device> ping 10.33.4.7

NOTE
If you address the ping to the IP broadcast address, the device lists the first four responses.

Tracing a route

To determine the path through which a device can reach another device, enter a command similar to the following at any level of the CLI on
the device.

device> traceroute 10.33.4.7

Monitoring the Device
Interpreting nonport-side LEDs

Ruckus ICX 7150 Switch Hardware Installation Guide

98

Part Number: 53-1004928-05

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды