Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 97

Страница: 97 / 123

TABLE 21 Diagnostics status LED during normal operation

LED color

Status of hardware

Recommended action

Off

System is functioning normally or the device did not perform
diagnostics test in the most recent reload.

None.

Flashing green

System self-diagnostic tests are in progress.

None.

Steady green

System self-diagnostic tests have successfully completed.

None.

Flashing amber

System self-diagnostic test has detected a fan, thermal, or interface
fault.

•

Check the syslog messages details.

•

Power cycle the device to try and clear the
condition.

•

If the condition persists, contact Technical
Support.

Power status LED

Refer to the following table to interpret the system power status LED.

TABLE 22 System power status LED during normal operation

LED color

Status of hardware

Recommended action

Off

No power

•

Check if internal power supply is disconnected.

•

Check the connections between the device,
the power cord, and the wall outlet.

•

Contact Technical Support.

Steady green

Internal power supply is working normally.

None.

Steady amber

Internal power supply for the PoE ports has failed.

Contact Technical Support.

OOB LED

Refer to the following table to interpret the OOB LED.

TABLE 23 Link status (Green): Left side LED

LED color

Hardware status

Recommended action

Off

Offline

None.

Steady green

Link is up.

None.

Flashing green

Packet transmission or reception is occurring at
the port.

None.

TABLE 24 Speed status (Green): Right side LED

LED color

Hardware status

Recommended action

Off

Offline or linked at 10/100 Mbps.

None.

Steady green

Linked at 1000 Mbps.

None.

RJ-45 Ethernet port status LED in default mode

Refer to the following table to interpret individual RJ-45 Ethernet port status LED in default mode.

Monitoring the Device

Interpreting port-side LEDs

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды