Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 87

Страница: 87 / 123

3. Gently insert the transceiver into the slot until it clicks into place. Transceivers are keyed to prevent incorrect insertion.

NOTE
The location of the fiber-optic interface shown is for illustration purposes only. They may be in a slightly different location
on the device you are using.

FIGURE 58 Installing a transceiver

1. Transceiver

NOTE
If a 1-Gbps optic transceiver is inserted, you must configure the port using the

speed-duplex 1000-full-master

command at the interface level.

Cabling a fiber-optic transceiver

Perform the following steps to cable a fiber-optic transceiver.

1. Remove the protective covering from the fiber-optic port connectors and store the covering for future use.

NOTE
Before cabling a fiber-optic transceiver, Ruckus strongly recommends cleaning the cable connectors and the port
connectors.

2. Gently insert the cable connector (a tab on each connector should face upward) into the transceiver connector until the tabs lock

into place.

3. Observe the link and active LEDs to determine if the network connections are functioning properly.

Installing Transceivers and Cables

Cabling a fiber-optic transceiver

Ruckus ICX 7150 Switch Hardware Installation Guide

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды