manualshive.com logo in svg

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Поделиться
Скачать
Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 54

The device can be installed so that the port side is either flush with the front posts or recessed with the non-port side flush with the rear
posts. A recessed position allows a more gradual bend in the fiber-optic cables connected to the device and less interference in the aisle at
the front of the rack.

NOTE
Hardware devices illustrated in these procedures are only for reference and may not depict the device you are installing into the
rack.

Time and items required

Allow 15 to 30 minutes to complete this procedure. Note the following requirements to ensure correct installation and operation.

The following items are required to install the device using the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks:

•

#2 Phillips torque screwdriver

•

1/4-inch slotted-blade torque screwdriver

Parts list

The following parts are provided with the 1U, 1.5U, and 2U Universal Kit for Four Post Racks Installation (XBR-R000295).

Mounting the Device
Time and items required

Ruckus ICX 7150 Switch Hardware Installation Guide

54

Part Number: 53-1004928-05

Содержание ICX 7150-24




























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды