Ruckus Wireless ICX 7150-24 Скачать руководство пользователя страница 104

Страница: 104 / 123

Condition

Operational

Non-operational

Shock

20 G, 11 ms, half-sine wave

33 G, 11 ms, half-sine wave

Vibration

1 G sine, 0.4 gms random, 5-500 Hz

2.4 G sine, 1.1 gms random, 5-500 Hz

Airflow

ICX 7150-48ZP: 40.36 CFM (Maximum), 14.6 CFM (Typical)

ICX 7150-C12P: 0 CFM

ICX 7150-24: 0 CFM

ICX 7150-24P: 37.6 CFM (Maximum), 13.4 CFM (Typical)

ICX 7150-48: 0 CFM

ICX 7150-48P: 38.15 CFM (Maximum), 13.9 CFM (Typical)

ICX 7150-48PF: 50.8 CFM (Maximum), 19.6 CFM (Typical)

N/A

Heat dissipation

Refer to Power Consumption specification sections

N/A

Operating noise

For all fanless ICX 7150 devices and devices in fanless
mode: Less than 12 dBA

ICX 7150-24P, ICX 7150-48P, and ICX 7150-48ZP with
fans running: Maximum of 52 dBA

ICX 7150-48PF with fans running: Maximum of 48 dBA
(fanless mode is not supported)

N/A

Power supply specifications (per PSU)

All the Ruckus ICX 7150 power supply units (PSUs) are fixed and internal to the device. All the PSUs use a C14 inlet and connect to
standard AC power.

Device

Maximum output
power rating (DC)

Input voltage

Input line frequency

Maximum input
current

Input line protection Maximum inrush

current

ICX 7150-48ZP

1740 W

100 - 240 VAC

(nominal)

90 - 264 VAC

(range)

50/60 Hz

(nominal)

47 - 63 Hz

(range)

13 A (rms)

Line fused

30 A at 115 VAC

60 A at 230 VAC

Cold start @ 25°C

ICX 7150-C12P

150 W

100 - 240 VAC

(nominal)

90 - 264 VAC

(range)

50/60 Hz

(nominal)

47 - 63 Hz

(range)

2.78 A (rms)

Line fused

40 A at 115 VAC

60 A at 230 VAC

Cold start @ 25°C

ICX 7150-24

36 W

100 - 240 VAC

(nominal)

90 - 264 VAC

(range)

50/60 Hz

(nominal)

47 - 63 Hz

(range)

3 A (rms)

Line fused

40 A at 115 VAC

80 A at 230 VAC

Cold start @ 25°C

For the ICX 7150-C12P, the maximum operating temperature is 40°C when under fully loaded PoE conditions or when installed using the long bracket

(ICX7000-C12-RMK) under a fixed surface. The maximum operating temperature is 35°C when installed using the short bracket (ICX7000-C12-WMK)

under a fixed surface.

Ruckus ICX 7150 Switch Technical Specifications
Power supply specifications (per PSU)

Ruckus ICX 7150 Switch Hardware Installation Guide

104

Part Number: 53-1004928-05

Содержание ICX 7150-24



























































































































Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7150-24, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7150-24

Отзывы:

Бренды по названию

Популярные бренды