RTA 460SCUS Скачать руководство пользователя

Страница: 68 / 70

Real Time Automation, Inc.

1-800-249-1612

Save and Replace Configuration Using SD Card

Saving Configuration Using SD Card

This function saves the gateway’s configuration automatically to an SD Card each time the gateway is

rebooted via the

Restart Now

button on the web page. If this unit should fail in the future, the last

configuration stored on the SD card and can be used for a new gateway to get the application back up
and running quickly.

This SD Card replaces every configurable field in the gateway,

EXCEPT

for IP Address, Subnet Mask, and

Default Gateway.

Replacing Configuration Using SD Card

To replace a configuration in a gateway using the SD Card, a specific sequence of events must be
followed for the replacement to happen correctly:

Extract SD Card from gateway you wish to copy the configuration from.

Power up the gateway you wish to copy the configuration to. DO NOT INSERT SD CARD YET.

Navigate to the webpage inside the unit.

Navigate to the dropdown

Other->Utilities

If you are not currently in

Mode: Configuration

, go into Configuration Mode by clicking the

Configuration Mode

button at the top left-hand side of the screen.

Press the

Revert to Manufacturing Defaults

button on the Utilities Page. The Configuration will

ONLY be replaced by the SD Card if the gateway does not have a configuration already in it.

When the unit comes back in

Mode: Running

, insert the SD Card.

Do a hard power cycle to the unit by unplugging power. DO NOT RESET POWER VIA WEB PAGES.

It will take an additional 30 seconds for the unit to power up while it is transferring the
configuration. During this time, the gateway cannot be accessed via the web page.

When the unit comes back up, the configuration should be exactly what was on the SD Card.

Содержание 460SCUS







































































Результаты поиска

Содержание 460SCUS

Отзывы:

Похожие инструкции для 460SCUS

Бренды по названию

Популярные бренды

RTA 460SCUS, Руководство пользователя

Результаты поиска

Содержание 460SCUS

Отзывы:

Похожие инструкции для 460SCUS

Бренды по названию

Популярные бренды