RSI MasterBath Скачать руководство пользователя страница 1

Page 1

33

1

/

2

"

81"

Figure 1

Tack in shims at

low points.

Mark the outlines of

all cabinet sizes on
the wall to check the

actual cabinet

dimensions against

your layout.

Strike level baseline from highest
point of floor.

UNEVEN FLOORS AND WALLS 

Because floors and walls have uneven spots which will affect the 

installation, it will be necessary to locate these uneven areas. Wall 

and floor unevenness can cause cabinets to be misaligned result-

ing in “racking” or misalignment of the doors and drawer fronts. 

Uneven spots can be found with a straight edge or a 4’ level. 

Simply run the straight edge along the floor and wall to identify 

any uneven areas. Where these uneven spots interfere, high spots 

can be removed by scraping or sanding the excess plaster. Low 

spots can be shimmed. 

LOCATE STUDS 

Locate the wall studs with a stud finder or tap on the wall to locate 

a “solid sound.” This generally will tell you where the wall studs are 

located. You can verify this location by driving a small finishing nail 

into the wall. Make sure this is an area that will be covered by the 

base cabinets. Mark a chalk line at the center of the wall studs at 

the top and bottom of the cabinet position. Normally the wall studs 

are located 16” apart, center to center. 

CABINET HEIGHT 

To establish the height of your base cabinets,measure up and mark 

the wall at 33

1

2

” from the highest spot on the floor. Use this mark 

as a starting point and draw the lines around the bathroom. Mark 

the outlines of all cabinets on the wall to check actual cabinet 

dimensions against your layout (Figure 1).

HARDWARE 

Decorative and installation hardware such as nails, screws, glue, 

tape, etc. are not included.

R37077

Rev. 11-11

Step 1. Preparation 

MasterBath & MasterBath Elite

Please read prior to installation

Содержание MasterBath













Отзывы: