RR Mechatronics STARRSED TL Скачать руководство пользователя страница 32

Страница: 32 / 137

5.3.2.1 - Display patient results

In the window Select date to show results: double click on the file name to select the results of the selected

date.

Press

Refresh

to refresh the list of available files.

In the window

Sample ID

, type the sample ID information and press

Search

Press

Options

for the following search options:

▪

Show today's results.

▪

Show today's results from a selected time frame of the day.

▪

Show results of a number of past days. Default value is set for 7 days.

▪

Show results of a specific day.

▪

Show results of the range between the first selected date to the next selected date.

From the selected Sample ID detailed information is shown on this screen.

Sample ID

Sample Identification number

Aspect code

Shows the aspect code (e.g. Hazy <10)

ESR 30 min

The 30 minute method is used. This is the measured 30 minutes value.

ESR 60 min

When the 60 minute method is used, this is the

measured

60 minutes value.

When the 30 minutes method is used, this is the

calculated

60 minutes

value.

ESR 60 min T.Corr

Temperature correction is used. This is the 60 minutes value corrected to

18°C.

Date / time

Date and time of the measurement of the result.

Starrsed TL program

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды