RR Mechatronics STARRSED TL Скачать руководство пользователя страница 126

Страница: 126 / 137

13.3 - Appendix - Error list Interrliner

Last updated: 08-10-2018

Error

Extra explanation

Reason/Solution

E2: Communication error! (Board: %s

(%x), Command: %x, TWSR: %x E:

%d)

Communication lost after 3 retries

between Computer and Interrliner.

•

Power cable not connected

on the communication PCB

mounted on the back panel.

•

An I2C cable not connected

•

Serial cable not connected

•

No power on one of the PCB's

•

Short circuit or fault on one

of the PCB's

E3: Measure motor timeout!

Measure head motor did not move or

motor is blocked.

•

Measure head is not at the

Home position.

•

Check the Home sensor.

•

Motor is faulty.

•

Motor driver on drive board is

faulty.

E5: Duplicated ID !!

Sample rejected. Sample already in

carousel.

•

Wait until sample is measured

•

Check general settings (Check

for duplicate ID's)

E6: Program was not properly shut

down. Check settings before

continuing!

There is a possibility that changed

settings which were not saved to disk

are lost.

•

Program stopped and

computer needed to be reset.

•

Computer reset after power

failure.

E7: Needle motor position error!

Timeout! (piercing)

Needle did not go up within a certain

time limit.

•

Needle motor is faulty.

•

Needle motor driver on

needle board is faulty.

•

Needle is blocked.

E8: Fillnozzle not in fill position!

Fill nozzle did not reach the fill position

within a certain time limit.

•

Fill nozzle motor is faulty.

•

Fill nozzle motor driver on

nozzle board is faulty.

•

Fill nozzle is blocked.

E9: Air flow failure!

ESR analyser unit was not able to get

a stable reading during the vacuum

test before aspiration the sample.

•

Check for leakage on the

pipette or fill nozzle.

E12: Dilution error: wrong or no

diluent flow. Check the diluter!

Diluter malfunction

•

Check diluent flow sensor

•

Check tubes diluter system

Appendix for Interrliner

126

MRN-164_2-EN Version 1.08 Starrsed TL

Содержание STARRSED TL










































































































































Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды

RR Mechatronics STARRSED TL, Инструкция по эксплуатации

Результаты поиска

Содержание STARRSED TL

Отзывы:

Похожие инструкции для STARRSED TL

Бренды по названию

Популярные бренды