RR Mechatronics EHST109621 страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 134

background image

4

General safety information

The instrument described in this manual is designed to be used by properly trained personnel only. For the

correct and safe use of this instrument it is essential that both operating and servicing personnel follow

generally accepted safety procedures in addition to the safety precautions specified in this manual.

▪

Execute your work according to this manual. Read the instructions before operating the instrument.

Observe all cautionary markings in the manual and on the instrument. Keep this manual for future

reference.

▪

Follow the bio-safety procedures when working with blood-contaminated parts.

▪

Be cautious to prevent stinging during cleaning or replacing the needle assembly.

▪

Repair can only be executed by trained and qualified personnel.

▪

Wear protective clothing.

▪

When the instrument is running it is not allowed to:

▪ Open and remove safety covers.
▪ Touch moving parts.

▪

It is not allowed to give access to the instrument to a non-authorised person at any time.

▪

Whenever it is likely that safety-protection has been impaired, the instrument must be made

inoperative and be secured against any unintended operation. The matter should then be referred to

qualified technicians.

▪

Safety protection is likely to be impaired if, for example, the instrument fails to perform the intended

measurements or shows visible damage or unusual smells, smoke, liquids are flowing out.

4.1 - Safety warning

When there was an incident with the Interrliner which caused damage to the instrument, please notify your

superior and your local equipment dealer before you continue using the instrument.

Example:

▪

A collision with a moving object or a person.

▪

Something falling on the instrument.

▪

Liquids spilling into the instrument.

4.2 - Moving parts protection

Applicable for instruments delivered after aug. 2015 or after installation of Modification kit EHST120923 (see

Service Bulletin IB 2015015)
The Interrliner is equipped with moving parts protection.
The sample robot unit is closed with a robot cover and automatically locked during sampling.
The cover of the tube handling unit (“robot cover”) is equipped with a locking device that automatically locks

the cover during operation. The robot cover cannot be opened during movement of the tube handling

mechanisms.

General safety information

MRN-164_2-EN Version 2.02 Interrliner

21

«
...
19
20
21
22
23
...
»

Содержание EHST109621







































































































































Отзывы:

Нет отзывов

Похожие инструкции для EHST109621

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: Sagola Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды