manualshive.com logo in svg

Royal Enfield Himalayan, Руководство по обслуживанию, Страница: 211 / 214

Поделиться
Скачать
Royal Enfield Himalayan Скачать руководство пользователя страница 211

ROYAL ENFIELD    HIMALAYAN BS III VEHICLE SERVICE MANUAL

210

WARNING

The trouble shooting section of this Service Manual is intended solely as a guide for diagnosing problems. Carefully

read the appropriate sections of this manual before performing any work. Repair and maintenance operations not

listed in this Owner’s Manual should be performed by your Royal Enfield Authorized Dealer only. Improper repair /

maintenance could result in the motorcycle not functioning properly or injury seriously.

CAUSES

REMEDIES

18. TROUBLE SHOOTING

I. ENGINE FAILS TO START

1)

Stop switch in ‘OFF’ Position

Push stop switch to ‘ON’ position.

2)

Side stand not retrieved

Retrieve side stand.

3)

Vent hole clogged in fuel tank cap

Clean vent hole.

4)

Spark plug cap / lead not connected

Fix cap / lead firmly

5)

Spark plug electrode dirty / fouled

Clean spark plug

6)

Spark plug insulation cracked

Replace spark plug

7)

Clutch slipping

*Adjust clutch cable free play

8)

Fuse failed

Replace with new fuse

II. ENGINE MISFIRING

1)

Loose spark plug gap

Fix cap / lead firmly

2)

Spark plug fouled

Clean spark plug or non specified heat range plug.

3)

Water in petrol tank

* Clean petrol tank. Fill tank with fresh petrol.

III. POOR PICKUP

1)

Brake pedal adjusted too tight

*Re-adjust properly

2)

Choked air filter

Clean / Replace air filter

3)

Rear chain adjusted too tight

*Re-adjust properly

4)

Under inflated tyres

*Inflate to correct pressure

5)

Accelerator cable free play excessive

Adjust cable free play

6)

Clutch Slipping

*Adjust clutch cable free play

 IV. WHITE/BLUE SMOKE

1)

Oil level in sump above the Top line.

*Check and drain excess oil

in the oil level window

V. ENGINE OVERHEATING

1)

Low engine oil level

Check and top-up if necessary

2)

Clutch slipping

* Check and correct

3)

Cylinder fins not clean

Clean the cylinder fins at regular intervals

VI. EXCESSIVE FUEL CONSUMPTION

1)

Under inflated tyres

Inflate to correct pressure

2)

Choked air filter

Clean / Replace

3)

Fuel leakage

*Check and rectify, tank float unit, drain pipe, breather

pipe, fuel line.

Содержание Himalayan























































































































































































































Отзывы:

Нет отзывов