Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 96

Страница: 96 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

6.5

Headlamp Casing &

Steering Stem

Bullet Classic EFI /

Bullet EFI



Using a short chisel, drive

in the ball race along with

dust cap on the

headlamp casing and the

ball race in steering

stem.



Loosen and remove the

steering stem lock nut

from the headlamp

casing along with the

washer.



Remove the fork cover

tubes LH & RH along with

the rubber spacers and

plastic bushes.



Locate steering stem

and assemble on the

frame.



Using a long chisel, gently

tap and drive in at the

top and bottom races on

the frame head tube

along with the dust cap.



Locate the top and

bottom ball cage from

the ball races.



Locate the Headlamp

casing in the frame.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 96 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: