Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 90

Страница: 90 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

6.5 Steering Play

Adjustment
Bullet Classic EFI /

Bullet EFI



Rock the front end and

feel the play at stem top

end

NOTE:

Every 6,000 KMS, Steering

Ball race adjustment should

be done and on Every

12,000 Km Lubrication is

recommended.

Lock Nut M20

Socket Spanner - 30 mm

Dome Lock Nut M24
Socket Spanner – 30 mm

Torque – 50 Nm



Finally tighten all the

nuts and bolts in reverse

order.

If felt, adjust as follows:



Loosen steering bottom

bridge pinch bolt and

nuts of Right & Left side



Loosen the stem lock nut

and then tight steering

stem tapper nut to

adjust excess play.



Again re-check play, it

should be free without

any play.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 90 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: