Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 79

Страница: 79 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

6.4 Front Fork LH & RH

Continental GT



Locate the fork assem-

bly LH & RH on the head

lamp casing and the

steering stem.



Gently rotate and locate

the forks LH & RH on the

steering stem and top

yoke.



Install the 4 hex socket

head cap bolts (2 each

on LH & RH sides) on the

top yoke.

NOTE:

Support the head lamp

holders with the trafficators

while removing the forks LH

& RH from the steering stem.

Hex Socket Screw M6
Allen key 5 mm

Hex Socket Screw M8
Allen key 6 mm



Install the 4 hex socket

head cap bolts (2 each

on LH & RH sides) on the

steering stem.



Install the 2 hex socket

screws inside the head

lamp holder RH & LH.

Ensure the head lamp

holders are fixed on the

front fork main tube.



Install and locate the 2

hex bolts holding head

lamp housing to the

holder RH & LH.



Locate Headlamp in the

headlamp housing and

connect all electrical

connections

inside

headlamp housing.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 79 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: