Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 59

Страница: 59 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

6.2

Front Mudguard

Bullet Classic EFI /

Bullet EFI



Locate Mudguard stays

along with mudguard

and slide into the fork

legs.



Install wheel speed

sensor screw and locate

sensor along with screw.



Install and locate:
- 2 flanged hex bolts

along with spring

washers, holding front

mudguard centre stay

& front brake caliper to

fork end LH.

- 2 flanged hex bolts

along with spring

washers, holding front

mudguard front and

rear stays to fork end

LH.



Install and locate the 4

flanged hex bolts along

with spring washers,

holding front mudguard,

front, centre & rear stays

to fork end RH.



Locate Brake hose

grommet in the holding

clip in front mudguard.



Assemble Front wheel

as described in

Front

Wheel section.

CAUTION:

Ensure mudguard does

not get scratched while

assembling.

Socket head cap Screw:

M6
Allen Key : 5 mm
Torque : 25Nm

Flanged Hex bolt: M8 X

38 & M8 X 20
Socket Spanner: 12 mm
Torque : 10 Nm

Flanged Hex bolt: M8 X

20
Socket Spanner: 12 mm
Torque : 10 Nm

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 59 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: