Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 57

Страница: 57 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle /

Instructions

6.2

Front Mudguard

Bullet Classic EFI /

Bullet EFI



Remove Front wheel

as described in

Front

Wheel section



Release Brake hose

grommet from the

holding clip in front

mudguard.



Loosen and remove the

4 flanged hex bolts along

with spring washers,

holding front mudguard,

front, centre & rear stays

to fork end RH.



Loosen and remove:
- 2 flanged hex bolts

along with spring

washers, holding front

mudguard centre stay

& front brake caliper to

fork end LH.

- 2 flanged hex bolts

along with spring

washers, holding front

mudguard front and

rear stays to fork end

LH.



Loosen wheel speed

sensor screw and

remove sensor along

with screw.



Gently rotate the

mudguard stays into the

mudguard and slide out

of the fork legs.

Flanged Hex bolt: M8
Socket Spanner: 12 mm

Socket head cap Screw:

M6
Allen Key : 5 mm

CAUTION:

Ensure mudguard does not

get scratched while tilting

and removing.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 57 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: