Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 43

Страница: 43 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

INSPECTION



Inspect Silencer and Exhaust assembles for any deep scoring / damages / dents as it might cause damage to the

internals and the catalytic converters.



Inspect silencer and exhaust pipe joint for any signs of exhaust gas leakage.

CAUTION :



Do not clean the silencer and exhaust internals with any solvents, gasoline etc as it will damage the catalytic

converters.

REPLACE



Gasket between the silencer and exhaust pipe joint whenever the silencer / exhaust pipe are dismantled.



Copper gasket between exhaust pipe and cylinder head whenever exhaust pipe is dismantled from cylinder

head.



Copper gasket in HEGO sensor whenever exhaust pipe / hego sensor is dismantled.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 43 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: