Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 30

Страница: 30 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

5.3 Fuel tank -

Assembly
Continental GT



Locate over flow tube

carefully into the Fuel

tank.



Install the fuel tank

towards front to mount

into front locking clamp

into the frame.



Place a piece of cloth

between handle bar

clamp bolt and fuel tank.



Gently lift up fuel tank at

the end and

- Connect low fuel

sensor coupler wire.

- Connect EVAP hose

into the Fuel tank.

- Connect fuel hose

into the Fuel tank.



Install 2 Hex bolts at the

rear end of fuel tank

along with washers,seals

and rear dampers.



Assemble Seat.



Fill fuel sufficiently.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

No.

Hex Flange Bolt M6
Socket Spanner 10 mm

Hex Flange Bolt M6
Socket Spanner 10 mm
Torque 5 Nm

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 30 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: