Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 29

Страница: 29 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

5.3 Fuel tank -

Assembly
Bullet Classic EFI/

Bullet EFI

Ensure the handle bar is

held at straight ahead

position.



Position fuel tank on

frame such that the front

mounting locate on the

rubber supports in the

frame.



Gently lift up fuel tank at

the end to:
- Connect low fuel

sensor coupler wire.

- Connect EVAP hose

to the Fuel tank.



Connect fuel hose to the

fuel tank.



Ensure the two dampers

and mounting sleeves

are properly located in

the mounting slots.



Ensure the mounting

are

aligned

and

assemble 2 hex bolts

with large washers.



Tighten the two bolts

evenly.



Assemble Seat.



Fill fuel in the tank.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

Place a piece of cloth on the

top, front portion of the

fuel tank to avoid damage

due to touching of the

handle bar clamp on fuel

tank.

No.

Hex Flange Bolt M6
Socket Spanner 10 mm

Torque 5 Nm

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 29 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: