Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 235

Страница: 235 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

234

12.1 Battery -

Dismantling

Bullet Classic EFI/

Bullet EFI



The battery is located on

the left side of the

motorcycle.



Ensure the motorcycle is

parked on its center

stand, in a well ventilated

area.



Ensure the ignition

switch and engine stop

switch are in OFF

position.



Unlock and remove the

battery cover.



Remove the two straps

holding the battery to

the battery carrier.



Pull the battery out

slightly from the battery

carrier.



Remove the battery

from the carrier.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

No.

NOTE :

Disconnect -VE terminal

FIRST and the +VE terminal

NEXT.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 235 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: