Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 229

Страница: 229 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

228

ROYAL ENFIELD NACS II DIAGNOSIS

Adjust CO value
by clicking
and click
to save
adjusted value.

12-20.

This software is for reading NACS II handheld
recorded data. Please take out SD card from NACS II
handheld tool and insert SD card to PC.

13. RECORD ANALYZING SOFTWARE

Open the
software of
‘NACSII_Record_Royal’.
Select ‘Analyze
Record Data’.

13.1.

Select Record Date
and File name, then
click

13-2.

Select the items
which used often.
Selected items will be
listed in the block of
‘Live Data Item’.
Click to view
wave chart of
selected items.

13-3.

13-4.

Wave chart starts running until press ‘Stop’ button.
Drag Yellow line forward and back to view recorded
live data values.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 229 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: