Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 215

Страница: 215 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

214

3. PRODUCT SPECIFICATION

4. HARDWARE CONNECTION

DIAGRAM

Connect NACS II-ROYAL diagnostic tool kit as below

before performing diagnosis.

1. HAND-HELD

NACS II - ROYAL interface



Main cable



Diagnostic

cable



Motorcycle (IG ON)

Dimension

L:173.78mm x

W:134.66mm x

H:60.91mm

Weight

660g

Operating Voltage

DC 8~18V

Operating Current

300mA

Operating Temperature

C~+70

Dust and water resistance IP55 Standard

5. WARNING



When NACS II is already connected to the

motorcycle, do NOT plug in AC Adaptor.



Do not remove SD card when you are using NACS

II.



The failure caused by the use of unapproved

cables, accessories is out of warranty.



The warranty will become void if NACS II is

disassembled or altered.



We recommend you to back up the SD-card data

to avoid data loss due to various reasons.

2. PC



USB Hi-Speed Cable



NACS II-ROYAL

interface



Main Cable



Diagnostic Cable



Motorcycle (IG ON)

‘

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 215 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: