Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 192

Страница: 192 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

191

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle /

Instructions

10.8

Fuel Pump

Assembly



The fuel pump assembly

is located inside the fuel

tank at the left side, rear

bottom.



Ensure Ignition switch

and stop switch are in

OFF position.



Remove Seat assembly

as described in

section

5.4 for seat dismantling.



Remove fuel tank as

described in

section

5.3 for Fuel tank

dismantling.



Loosen & remove 5 Hex

Socket Button Head Cap

Screws along with the

copper & fibre washers.



Remove clamp plate.



Pull out fuel pump from

the fuel tank.



Take care to remove the

O ring from the fuel tank.

CAUTION:



Store fuel in a tight

sealed container in a

well ventilated, cool

and dry place.



Do not smoke or allow

open flame or sparks in

the vicinity.

NOTE:

Ensure Ignition switch and

engine kill switch are in OFF

position
Drain fuel completely from

fuel tank before removing

fuel pump.

Hex Soc Button Hd Cap

Screws: M6 X 12
Socket spanner: 8mm

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 192 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: