Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 179

Страница: 179 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

178

4. HEGO SENSOR ( O2/LAMBDA SENSOR)

The HEGO sensor is located on the exhaust down pipe, just after the cylinder head.

SPECIFICATION

Operating Voltage : 16V (Max)
Operating temperature: 600ºC - 950ºC

It detects residual oxygen in the exhaust gases versus the amount of oxygen in the atmosphere and provides the

data on a real time basis to the ECU based on which the fuel injection is metered continuously to control exhaust

emissions and for optimum performance of the motorcycle.

5. EXHAUST AIR INJECTION UNIT (SOLENOID)

The exhaust air injection unit (EXAI) is located underneath the fuel tank.

In addition to the Hego sensor, the EXAI gets inputs from the ECU to supply filtered air into the exhaust end of the

cylinder head, primarily during idling RPM so as to meet exhaust emission specifications.

SPECIFICATION

Operating voltage : 10 V to 14.5 V
Operating Temperature: - 20°C to +120°C

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 179 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: