manualshive.com logo in svg

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 115 / 301

Поделиться
Скачать
Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 115

ROYAL ENFIELD    VEHICLE SERVICE MANUAL - EURO IV

114

S.

No.

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

7.3

Rear Shock absorber

Adjustment

Bullet Classic EFI /

Bullet EFI /

Continental GT

The Pre-loaded  spring

tension shockabsorber

is of adjustable type i.e.,

the spring tension can be

increased or reduced.

The spring tension of the

rear  shockabsorbers

can  be  increased  or

decreased  to  suit

different riding conditions.

The adjuster provided at

the bottom of the spring

has five notches and can

be  rotated  using  a

special ‘C’ spanner.

Rotate adjuster “clock-

wise” to increase spring

tension  and  “anti-

clockwise”  to  reduce

spring tension.

Ensure  the  spring

tension is  the same in

both the left and right

side shockabsorbers

After 

adjustment,

ensure  the  adjuster

notches  are  seated

correctly against the peg

in the shockabsorber.

CAUTION:

Riding the motorcycle with

the  notches  adjusted  in

different  positions  can

cause loss of control and

may  lead  to  an  accident.

Regularly  inspect  shock-

absorbers and front forks

for  leaks.  Replace  worn

parts.  Worn  parts  can

adversely affect  stability

and handling.

Special Tool:
C Spanner

NOTE:

Ensure  no fouling  of  any

accessories with rear Shock-

absorber.  Check  for

sufficient gap availability

between the shockabsorber

and the attachments when

the rear end of the motor-

cycle is fully loaded and the

shock absorbers are fully

compressed.

C5/B5

GT

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Отзывы:

Нет отзывов