Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 113

Страница: 113 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

112

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

7.2 Drive chain free

play adjustment



To increase the free play,

turn the drive chain

slack adjusting nut at

each end of the swing

arm in anticlockwise

direction and push the

rear wheel forward.



Check the front and rear

wheels correctly aligned.



Check and ensure the

alignment marks on each

side of the swing arm.



Finally torque the castle/

spindle nut



Tighten the lock nut for

the chain slack adjusting

nut.

CAUTION:

Improper drive chain slack

will overload the engine

and It leads to chain

slippage or breakage. It is

recommended to maintain

drive chain slack within the

specified limits.

Torque: 70 Nm

Hex lock nut M8
Double end spanner – 13

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 113 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: