Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 100

Страница: 100 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

6.5 Top Yoke & Steering

Stem
Continental GT



Using a short chisel, drive

in the ball race along with

dust cap in the top yoke

and the ball race on

steering stem.



Using a long chisel, gently

tap and drive in at the

top and bottom races

from the frame head

tube along with the dust

cap.



Locate the top and

bottom ball cage in the

ball races.



Locate steering stem

and assemble on the

frame.

NOTE:

Replace all Rubber parts, ,

plastic bushes, O rings,

washers whenever they are

removed.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 100 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: