Royal Enfield Bullet Classic EFI Скачать руководство пользователя страница 10

Страница: 10 / 301

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

SECTION 04 -

ENGINE REMOVAL FROM FRAME

ROYAL ENFIELD VEHICLE SERVICE MANUAL - EURO IV

Bullet Classic EFI / Bullet EFI / Continental GT



Disconnect alternator leads.



Disconnect the spark plug suppressor cap.



Disconnect the fuel pipe.



Remove throttle body along with throttle cable.



Remove the air filter assy.



Remove the exhaust pipe and silencer.



Disconnect the engine steady bolt.



Remove the rear chain.



Remove the LH Foot rest.



Support the engine on a suitable box or wooden block.



Remove the center stand and the stand stop.



Remove the front engine plates and the small bolt fixing the stand spring bracket.



Remove the stud securing the rear engine plate to the frame Slide out the engine.

KS MOTORCYCLES - http://ksmotorcycles.com

Содержание Bullet Classic EFI














































































































































































































































































































Результаты поиска

Содержание Bullet Classic EFI

Отзывы:

Royal Enfield Bullet Classic EFI, Руководство по обслуживанию, Страница: 10 / 301

Результаты поиска

Содержание Bullet Classic EFI

Отзывы: