background image

iv  

  Important Safeguards 

X935-24-00  Rev 108 V894CSH/V894WSH High-Security Cameras 

Vicon dealer or local power company. For video 
products intended to operate from battery power, or 
other sources, refer to the operating instructions.  
 

11. Grounding -

 This applies to video products 

equipped with a 3-wire grounding-type plug, a plug 
having a third (grounding) pin. This plug only fits into a 
grounding-type power outlet. This is a safety feature. If 
you are unable to insert the plug into the outlet, contact 
your electrician to replace your obsolete outlet. Do not 
defeat the safety purpose of the grounding-type plug. 
 

12. Power-Cord Protection -

 Power supply cords 

should be routed so that they are not likely to be walked 
on or pinched by items placed upon or against them, 
paying particular attention to cords at plugs, 
convenience receptacles, and the point where they exit 
from the video product. 
 

13. Outdoor Cable Grounding -

 If an outside cable 

system is connected to the video product, be sure the 
cable system is grounded so as to provide some 
protection against voltage surges and built-up static 
charges. Section 810 of the National Electrical Code, 
ANSI/NFPA 70-1984, provides information with respect 
to proper grounding of the lead-in wire to an antenna 
discharge unit, size of grounding conductors, location of 
antenna-discharge unit, connection to grounding 
electrodes, and requirements for the grounding 
electrode.  
 

14. Lightning -

 For added protection for this video 

product when it is not used for long periods of time, 
disconnect it from its power source and from the cable 
system. This prevents damage to the video product due 
to lightning and power-line surges. 
 

15. Power Lines -

 An outside cable system should not 

be located in the vicinity of overhead power lines or 
other electric light or power circuits, or where it can fall 
into such power lines or circuits. When installing an 
outside cable system, extreme care should be taken to 
keep from touching such power lines or circuits as 
contact with them might be fatal. 
 

16. Overloading -

 Do not overload wall outlets and 

extension cords as this can result in a risk of fire or 
electric shock. 
 

17. Object and Liquid Entry -

 Never push objects of 

any kind into this video product through openings as 
they may touch dangerous voltage points or short out 
parts that could result in a fire or electric shock. Never 
spill liquid of any kind on the video product. 
 

18. Servicing -

 Do not attempt to service this video 

product yourself as opening or removing covers may 
expose you to dangerous voltage or other hazards. 
Refer all servicing to qualified service personnel. 
 

19. Damage Requiring Service -

 Disconnect this video 

product from its power source and refer servicing to 
qualified service personnel under the following 
conditions. Note that step 

c

 does not apply to outdoor 

camera housings, outdoor pan-and-tilt drives and other 
equipment specifically designed for direct exposure to 
outdoor environments. 
 

a.  When the power-supply cord or plug is damaged. 

b.  If liquid has been spilled, or objects have fallen into 

the video product. 

c.  If the video product has been exposed to rain or 

water. 

d.  If the video product does not operate normally by 

following the operating instructions. Adjust only 
those controls that are covered by the operating 
instructions, as an improper adjustment of other 
controls may result in damage and will often require 
extensive work by a qualified technician to restore 
the video product to its normal operation. 

e.  If the video product has been dropped or the cabinet 

has been damaged. 

f.  When the video product exhibits a distinct change in 

performance - this indicates a need for service. 

 

20. Replacement Parts -

 When replacement parts are 

required, be sure the service technician has used 
replacement parts specified by Vicon or that have the 
same characteristics as the original part. Unauthorized 
substitutions may result in fire, electric shock, or other 
hazards. 
 

21. Safety Check -

 Upon completion of any service or 

repairs to this video product, ask the service technician 
to perform safety checks to determine that the video 
product is in proper operating condition.

 

 

 

Содержание Roughneck V894WSH























Отзывы: