background image

Page 6 of 16 

 

3. INSTALLATION OF DROP TRAY 

Use one or two bolts and nuts (NOT INCLUDED) to secure the drop tray. 

 
4. INSTALLATION OF CONTROL VALVE 

①.

 Apply appropriate thread sealant around the male thread of flexible spout, and then screw the flexible 

spout to the meter. 

②.

 Assemble the rubber cover to the meter. 

③.

 Apply appropriate thread sealant around the male thread of hose reel, then connect the male thread into 

the female thread of oil inlet of the control valve, and fix them together. 

④.

 Turn on all check valves of oil system. 

⑤.

 Press the trigger to drain enough oil to make sure the oil system is completely cleaned. See 

“OPERATION INSTRUCTIONS” section for the control valve operation. 

NOTE: 

To ensure the meter accuracy, purge all air out from the fluid lines and control valve before using 

them. 

OPERATION INSTRUCTIONS 

 

WARNING:

   

 

Never operate the meter with the plastic cover removed.

 The cover protects the meter from damage 

due to impact. Meters are sealed in the factory to keep moisture and dirt away.   

  Flush the lines before you install this equipment in the system to prevent line contamination, or it can 

cause equipment malfunction or damaged. 

  To reduce the risk of a serious bodily injury, including fluid injection, never exceed the maximum working 

pressure of the kit you are using or of the lowest rated component in your system. 

1. PRESSURE RELIEF PROCEDURE 

  WARNING:

 

Skin injection hazard:

 The equipment stays pressurized until pressure is manually relieved. 

To reduce the risk of serious injury from pressurized fluid, fluid from the valve or splashing fluid, follow this 
procedure whenever you:   

  Are instructed to relieve pressure 

  Check, clean or service any system equipment 

  Install or clean dispensing devices 

(1) Pressure relief procedure 

①.

 Turn off the air supply to the pump. 

②.

 Hold a metal part of the control valve firmly to a grounded metal waste container and point the valve 

outlet toward the waste container, then trigger the control valve to relieve the fluid pressure. 

③.

 Open any bleed-type master air valves and fluid drain valves in the system. 

Floor Mounting 

 

Wall Mounting 

 

Ceiling Mounting 

 

Fig. 2 

Содержание 28804


















Отзывы: