background image

Keeping the World Flowing

11

10.  Regulatory Information

11.  Passwords

USA-Federal Communications Commission (FCC)

This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of FCC Rules. These limits are 
designed to provide reasonable protection against 
harmful interference in a residential installation.

This equipment generates, uses, and can radiate 
radio frequency energy. If not installed and used 
in accordance with the instructions, it may cause 
harmful interference to radio communications. 
However, there is no guarantee that interference 
will not occur in a particular installation.

If this equipment does cause harmful interference 
to radio or television reception, which can be 
determined by tuning the equipment off and 
on, the user is encouraged to try and correct the 
interference by one or more of the following 
measures:

•   Reorientate or relocate the receiving antenna.

•   Increase the distance between the equipment 

and the receiver.

•   Connect the equipment to outlet on a circuit 

different from that to which the receiver is 
connected.

•   Consult the dealer or an experienced radio/TV 

technician for help.

Any changes or modifications not expressly approved  
by the party responsible for compliance could void 
the user’s authority to operate the equipment.

CAUTION:  
EXPOSURE TO RADIO FREQUENCY RADIATION.

This device must not be co-located or operating in 
conjunction with any other antenna or transmitter.

Canada – Industry Canada (IC)

This device complies with RSS 210 of Industry 
Canada.

Operation is subject to the following two 
conditions:

(1)  this device may not cause interference, and

(2)  this device must accept any interference, 

including interference that may cause undesired 
operation of this device.

L‘utilisation de ce dispositif est autorisée seulement 
aux conditions suivantes:

(1)  il ne doit pas produire d’interference et 

(2)  l’utilisateur du dispositif doit être prêt à 

accepter toute interférence radioélectrique 
reçue, même si celle-ci est susceptible de 
compromettre le fonctionnement du dispositif.

CAUTION:  
EXPOSURE TO RADIO FREQUENCY RADIATION.

The installer of this radio equipment must ensure 
that the antenna is located or pointed such that it 
does not emit RF field in excess of Health Canada 
limits for the general population; consult Safety 
Code 6, obtainable from Health Canada’s website 
www.hc-sc.gc.ca/rpb 

Brazil only

This equipment operates as secondary 
functionality, that is not entitled to protect from 
harmful interference, even for stations of the same 
type, and cannot cause interference to systems 
operating as primary functionality.

 

Insight 2

IQ Range / CK Range / SI Range

CVA Range

SI Pro Range

View

ROTORK

ROTORK

VIEW

PASSWORD

User

ROTACT

ROTACT

SULIS

PASSWORD

Содержание BTST v1.1













Отзывы: