background image

ROTORCOMP VERDICHTER

Operating Manual - 

EVO

®

 Line

4.2

[en] 07/2020

4.3 Transporting unpacked system

The screw compressor air end can be moved with 

a crane or with a lift truck or forklift truck when fas-

tened to a transport pallet.

Warning:

Death or serious injuries due to falling cargo!

– Observe the local safety regulations!

– Select the lifting equipment in accordance with 

the total weight to be transported!

– Remove all loose or swinging parts before lift-

ing the screw compressor air end! 

– Remove drive or body components before-

hand!

– Only transport the compressor air ends while 

depressurized!

– When transported on a pallet, the compressor 

air end must be securely fastened to it!

– Do not transport the compressor air ends on 

the forks of a stacker or lift truck!

– Transport eyes are only designed for transport-

ing the compressor air ends!

– Do not stand or walk under cargo during trans-

port!

– The air end must not contain oil, connections 

must be sealed with a plug or other suitable 

means.

To transport on a pallet, secure the screw com-

pressor air end on the pallet with angle brackets.

Figure 4-1

Содержание EVO15





































Отзывы: