Rotex RKHWMX300C Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 72

Rotex RKHWMX300C Скачать руководство пользователя страница 40

40

FA ROTEX HPSU monobloc compact • 09/2017

6

x

Taking out of operation

Ɣ

Unscrew the threaded piece on the filling and draining
connection (fig. 6-4, item E), remove the sealing plug
(fig. 6-4, item F)

and immediately

screw in

the pre-installed

threaded insert with

KFE filling connection

again into the

filling and draining connection (fig. 6-4).

Ɣ

Open the KFE cock on the

KFE filling connection

and

drain the water content of the storage tank.

Only with

solar system

Ɣ

Adjust the valve insert on the connection bracket so that the
path to the blind plug is blocked off (fig. 6-5).

Ɣ

Place a suitable collecting tray and remove the blind plug
from the connection bracket (fig. 6-5).

Ɣ

Open the KFE cock on the

KFE filling connection

.

Ɣ

Adjust the valve insert on the connection bracket so that the
path to the drain hose is open (see also fig. 6-5) and drain the
water content of the storage tank.

6.1.2 Draining the heating circuit and hot water

circuit

Ɣ

Connect the drain hose to the KFE cock of the ROTEX HPSU
monobloc compact.

Ɣ

Open the combined filling and draining valve on the ROTEX
HPSU monobloc compact.

Ɣ

Drain the heating and hot water circuits.

Ɣ

Disconnect the heating flow and return flow as well as the cold
water inflow and the hot water outflow from the ROTEX HPSU
monobloc compact.

Ɣ

Connect the discharge hose on the heating flow and return
flow as well as the cold water inflow and hot water outflow so
that the hose opening is at ground level.

Ɣ

Allow the individual heat exchangers to run empty one after
the other based on the suction lifter method.

CAUTION!

After removing the sealing plug, storage tank
water surges out.

Fig. 6-3

Completing the KFE fill-
ing connection

Fig. 6-4

Screwing the KFE filling
connection into the fill-
ing and draining con-
nection

Fig. 6-5

Shut off the valve insert, remove the blind plug from the con-
nection bracket

F

E

1.

2.

3.

4.

Ɣ

Insert the

KFE filling

connection

in the

connection bracket and
secure with holding clamp
(fig. 6-6).

Fig. 6-6

Installing the KFE filling
connection in the con-
nection bracket

«
...
38
39
40
41
42
...
»

Содержание RKHWMX300C









































































Отзывы:

Нет отзывов