Rotary Gate Systems SL-1000 R, Руководство пользователя

Страница: 4 / 25

4
Pre-installation Information
Before you begin…
Before unpacking, inspect the carton for exterior damage. If
you find damage, advise the delivery carrier of a potential
claim. Inspect your package carefully .
Claims for shortages
will be honored for only 30 days from the date of shipment.
Before installing the operator, read this manual completely to
ensure all requirements for proper installation are present.
Verify that the voltage to be used matches the voltage of the
operator.
If you have any questions about the requirements for proper
installation of this gate operator contact technical support at 1 -
877-331-4747.
Always Check the Gate’s Action
It’s very important before installing the gate operator to
make sure the gate slides free and level throughout the
entire opening distance. If the gate does not seem to
operate properly, it may affect the operator performance
or greatly shorten the life of the unit. The gate should also
be designed so that airflow is ample to prevent wind
resistance and dra g.
Gate Operator Classifications
All gate operators can be divided into one of four different
classifications, depending on their design and usage. Install
this gate operator only when the operator is appropriate for the
construction and usage class as defined below:

Class I Residential Vehicular Gate Operator
A vehicular gate operator intended for use in a home or for one to
four single family dwellings with a common garage or parking
area associated with these dwellings.

Class II Commercial/General Access Vehicular Gate Operator
A vehicular gate operator intended for use in a commercial
location or building such as a multi -family housing unit of five or
more single family units, hotel, retail store or other building
servicing the general public.

Class III Industrial/Limited access Vehicular Gate Operator
A vehicular gate operator intended for use in an industrial location
or building such as a factory or loading dock area or other location
not intended to service the general public.

Class IV restricted Access Vehicular Gate Operato r
A vehicular gate operator intended for use in a guarded industrial
location or building such as an airport security area or other
restricted access locations not servic ing the general public, in
which unauthorized access is prevented via supervision by
security personnel.
Approved Obstruction Detection Devices
The following contact or non -contact obstruction detection
devices have been approved for use with this slide gate
operator as part of a UL325 compliant installation:

Contact Edges
Miller Edge Models MGR20, MGS20, ME120

Photoeyes
MMTC Model IR-55 (165’ range)
MMTC Model E3K (28’ range)
Safety Information and Warnings
THE FOLLOWING FORMATS ARE USED FOR
SAFETY NOTES IN THESE INSTRUCTIONS.
Regulatory Warnings
Read the following before beginning to install this slide
gate operator:
WARNING
CAUTION
WARNING
This type of warning note is used to indicate
the possibility of damage to the gate or gate
operator.
This type of warning note is used to
indicate possible mechanical hazards that
may cause serious injuries or death .
This type of warning note is used to
indicate possible electrical shock hazards
that may cause serious injuries or death.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH TO
PERSONS, REVIEW THESE INSTALLATION SAFETY STEPS
BEFORE PROCEEDING
1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
2. ALL ELECTRICAL CONNECTIONS TO THE POWER
SUPPLY MUST BE MADE BY A LICENSED ELECTRICIAN
AND MUST OBSERVE ALL NATIONAL AND LOCAL
ELECTRICAL CODES.
3. A separate power-disconnect switch should be located near
the operator so that primary power can be turned off when
necessary.
4. Install the enclosed warning signs on both sides of the gate.
A minimum of two (2) warning signs shall be installed, one
on each side of the gate where easily visible.
5. Never reach between, thro ugh or around the fence to operate
the gate.
6. Never connect a button station within reach of the gate or on
the side of the gate operator.
7. Do not adjust the operator controller’s current sensing feature
too high. It should be adjusted high enough to keep t he gate
from falsely triggering the sensing, but no higher than
necessary for the gate to operate. DO NOT DEFEAT THE
PURPOSE OF THIS FUNCTION!
8. You must install all required safety equipment.
9. UL325 Compliance requires the use of contact edges of
photoelectric controls on all automatic or remotely -controlled
gate operators.
10. The operator is intended for installation only on gates used
for vehicles. Pedestrians must be supplied with a separate
access opening. The pedestrian access opening shall be
designed to promote pedestrian usage. Locate the gates
such that persons will not come into contact with the
vehicular gate during the entire path of travel of the
vehicular gate.