Before you begin...
4
Ensure that you have sufficient space to work and allow at
least
ONE HOUR
for assembly, particularly if you have never
built a unit before. We recommend
two-person
assembly.
4
Always use a rubber mallet for assembly and
NEVER
a metal hammer. Please note:
force is required
! The
components are designed to fit tightly together so that they
don’t wobble or break apart, so a light tap will
NOT
locate the
parts sufficiently.
4
We recommend wearing gloves when assembling.
Thank you for purchasing your
ShelvingDirect® shelving
If you have any questions regarding the
assembly or contents of your order, please call
ShelvingDirect® on
0121 508 5877
Monday to Friday 8.30am–5.30pm or email
ShelvingDirect® is a trading name of Rotadex
Systems Ltd, Systems House, Central Business Park,
Mackadown Lane, Birmingham B33 0JL.
Assembly instructions
STEP 1:
Arrange the four uprights
[A]
so that the
“keyholes” have the larger aperture uppermost:
STEP 2:
Begin by attaching the heavy duty plastic feet
[B]
to the
base of the upright posts.
STEP 3:
With one person holding two uprights parallel, join them
by adding a side beam
[C]
near the top (at the desired level for the
uppermost shelf) by striking its lugs firmly down into the “keyholes”
of the uprights using a rubber mallet. Force is required.
NOTE:
the lugs do not need to go completely to the bottom of the
keyholes.
Pinch the side beam and upright together using thumb
and forefinger directly between the lugs to ensure they are located
before hammering.
STEP 4:
Add a second side beam
[C]
near the bottom and at the
desired level for the lower shelf level.
STEP 5:
Add the remaining two side beams
[C]
, spacing them as
you require. Using this first sub-assembly as a ‘spacing guide’,
repeat this process with the other two uprights to create another
“ladder”. These form the left and right sides of your shelving unit.
STEP 6:
Take a cross beam
[D]
and join the two “ladders” together
by attaching it near the top, at the same height as the uppermost
side beams. Repeat at the bottom.
STEP 7:
Add cross beams
[D]
to the back of the unit too, and fit all
remaining cross beams ensuring they are located at the same height
as their corresponding side beams
[C].
STEP 8:
If you have purchased an wide unit, tap in the
centre support beams
[E]
. You may need to push the cross beams
[D]
towards one-another to do this.
STEP 9:
Lastly, add the shelf levels
[F]
. You will find it easier to
swivel the shelves in at an angle. The shelves are slightly smaller
than the space they fill, to aid assembly.
[C]
[D]
[E]
[F]
GALV WOR LOUVRE PANEL
GALV WOR LOUVRE PANEL
BEFORE YOU BEGIN!
n
Ensure that you have sufficient
space to work and allow at least
ONE HOUR for assembly, particularly
if you have never built a unit before.
n
We recommend two-person
assembly.
n
Always use a rubber mallet for
assembly and NEVER a metal
hammer. Please note: force is
required! The components are
designed to fit tightly together so
that they don’t wobble or break
apart, so a light tap will NOT locate
the parts sufficiently.
n
We recommend wearing gloves
when assembling.
PAGE 1 of 2
PLEASE CHECK YOUR COMPONENTS
Half Shelf Width Beam
2400mm.
Qty 4
Top Shelf Depth
Beam 600mm.
Qty 2
Heavy Duty Rear
Upright 1437mm. Qty 2
Half Shelf Depth
Beam 600mm.
Qty 4
Top Shelf Width
Beam 2400mm.
Qty 2
Heavy Duty Shelf
Support 600mm.
Qty 2
Heavy Duty Shelf Support
310mm.
Qty 4
Upper Shelf 2390mm
wide x 590mm deep.
Qty 1
Lower Shelf 2390mm
wide x 304mm deep.
Qty 2
Louvre Panel.
Qty 1
Plastic Feet.
Qty 4
4.8X13 size
self-tapping
screws. Qty 16
Width Louvre Beam.
Qty 1
M6 size bolts
with serrated
nuts. Qty 28
Upright Louvre.
Beam. Qty 1
Beams
Shelf Supports
Upright Posts
Shelves
Louvre Panel
Fixings and Feet
Accessories
Assembly Gloves and
Rubber Mallet.
Spanner for self-tapping screws.
Heavy Duty Front
Upright 929mm.
Qty 2
A
B
C
D
E
F
G
H
I
J
K
L
M
N
A
B
B
C
E
E
E
E
D
D
F
F
G
H
I
J
K
L
M
M
N
These are the component parts required to assemble your galvanised
workbench with louvre panel. Please take time to indentify each part
before you begin assembly! NOTE: You will also need a screwdriver and a
spanner or socket wrench suitable for an M6 nut.
WE RECOMMEND
2 PERSON
ASSEMBLY
NOTE: You will also need
a screwdriver and a
spanner or socket wrench
suitable for an M6 nut.
RGWB