CONTENTS
FEATURES
HOW TO INSTALL MIRROR MONITOR
AUTOMATIC NIGHT TIME SCREEN DIMMING
REAR VIEW NIGHT TIME DIMMING FUNCTION
MENU SETTING
SPECIFICATIONS
DISPLAY OPERATION
The package contains the following:
01 Rearview mirror monitor
02 wire harness
03 User's manual
04 wire cover
05 Remote control
REVERSE IMAGE:
LEFT OR RIGHT LANE:
FRONT:
Main button use:
One Touch Front Camera Viewing
Automatic LCD Brightness Adjustment
Ultra High Brightness Screen
Adjustable Back up Guide Line
Front, Rear, and Side Camera Inputs
Screen Brightness: 1000CD/m
2
Screen Size: 4.3 inch
Compatiable Systems: PAL / Auto / NSTC
Resolution: 480(H) X 272(V)
Working Voltage: 12V DC
Display Type: TFT-LCD
In dark environments or at night the screen will automatically reduce the
brightness level for better viewing. This level can be adjusted in the settings
menu.
In daytime and bright environments the screen will increase the brightness
automatically for better viewing.
Note:
When direct sunlight or headlamps shine into the mirror this may wash
out the picture and the ability to see your image.
The control under the mirror allows the driver to adjust the reflection from
high beam headlamps of vehicles approaching from behind. Flip the switch
at the bottom of the mirror forward to change the mirror angle and dim the
mirror as needed.
To return to normal view, flip the switch towards the rear of the vehicle.
02
01
04
05
Remote control
Menu setting guidance
Short press “ ”, you can switch among “PICTURE”, “SYSTEM”, or exit
out. When you enter either, press “ ” to switch among the items.
“ ” and “ ” are used to change the setting of each option.
Enter the menu
Guide line clockwise
Menu parameter decreases
Menu parameter
increases
Guide line up
Guide line left
Enter guide line
adjustment
Guide line anti-clockwise
Guide line right
Guide line down
PICTURE
BRIGHTNESS
50
50
50
CONTRAST
COLOR
SYSTEM
SCALE
ON
ON
OFF
REAR TRI
PRESET
Left
Left
Back
Front
Front
Right
Right
Back
While in reverse mode:
Press to adjust Brightness level UP.
While in stand-by mode:
Show Front view camera for 20 seconds.
03
1.The Reverse Camera input will always take priority over all other cameras.
When the vehicle is placed into reverse gear the camera image will automat-
ically be shown on the mirror display. While viewing the rear camera you
may adjust the panel brightness by pressing the center button on the mirror.
Each press will increase the brightness, keep pressing to return to the
starting level.
2. Blindspot cameras mounted on the sides of the vehicle are triggered by
the turn signals. When the driver signals to turn or change lanes the image
will be shown on the monitor. ( Blind Spot Cameras optional)
3. The front input can be controlled 2 ways depending on the installation.
1: By pressing the button on the front of the monitor it will display the front
camera for 20 seconds and then reset. 2: By using the trigger method the
monitor will show the input as long as the trigger is active. Note: The rear
camera will always override any input.
Removing the original mirror
CAUTION:
DO NOT USE EXCESSIVE FORCE WHEN REMOVING MIRROR
FROM THE WINDSHIELD MOUNT. THE WINDSHIELD BUTTON MAY SEPARATE
FROM THE WINDSHIELD OR THE WINDSHIELD MAY BREAK IF FORCED.
NOTE:
There are several versions of mirror mount systems. If unfamiliar with
mirror removal, seek professional assistance.
Screw mount mirror removal.
Using a Philips screwdriver or #20 Torx bit, loosen the screw in the base of
the mirror.
After loosening screw, gently lift upward to slide mirror off of mirror mount.
Wedge mount mirror removal procedure:
(Common for screw less mount).
Using a mirror tool or small 1/8” (4 mm) flat-blade screwdriver, insert the
flat end into the opening at the bottom of the mirror mount at the windshield.
Slide the screwdriver into the center of the mirror mount until resistance is
felt.
Gently apply a small amount of additional upward force to lift away locking
spring in the mount.
While still applying upward pressure with the screwdriver, grasp the mirror
bracket and wiggle side to side. Lift mirror up toward the headliner and off
the windshield mount button.
Mirror Installation.
Installation will vary depending on the mounting foot you use for the vehicle.
The mount pre-installed on the mirror is for a standard wedge mount foot. If
you need to use a different foot, change the foot by removing the Philips
head screw in the center of the foot. Attach the required foot to the mounting
arm with the included screw.
NOTE:
Check to insure the center screw in the mounting foot is tight before
installation to the windshield. The center screw should be tightened to 15
in-lb. If changing the mount, we recommend using Loctite Threadlocker to
insure the mount will not loosen over time. Install the mirror by reversing the
removal process.
NOTE:
Always use caution, DO NOT force the mount. Rostra Precision
Controls, Inc. will not be responsible for broken windshields. If you are not
sure how to remove or re-install the mirror seek trained, qualified help.
The monitor automatically detects the light level with
the photo sensor on the left side of the control
button. Do not block this sensor or this function will
not work correctly.
The menu is accessed and set by using the remote control.
Picture:
These settings will
adjust the picture attributes.
System:
These setting effect operational
features.
SCALE:
Turns parking lines ON/ OFF.
REAR TRI:
Turns the rear cam trigger
ON/OFF. If off the monitor will show the
image when present, when on the trigger
wire must be used.
PRESET:
Returns all settings to factory
default.
