Rosslare EX-x22 Скачать руководство пользователя страница 1

EX-x04 and EX-x22 

Sensitive Piezoelectric Button Switch 
Passive Infrared Motion Sensor Switch 

Installation Manual

 

1.

 

Introduction 

The EX-H04 and EX-M04 are sensitive piezoelectric button switches. 
The new access control switches are designed as flush mounting for US 

and UK electric boxes with piezoelectric technology. The switches have 
a red/green LED ring to display the switch status. 
The switches are designed as Request-to-Exit (REX) buttons for access 

control systems, direct activate electric strike, or magnet locks with up 
to 30 VDC and 1A. 
 

Figure 1: EX-H04 

 

Figure 2: EX-M04 

 

The EX-H22 and EX-M22 are passive infrared motion sensors (no touch 
switch). The new access control switches are designed as flush 

mounting for US and UK electric boxes with passive infrared 
technology The switches have a red/green LED ring to display the 

switch status. 
The switches are designed as Request to Exit (REX) buttons for access 
control systems, direct activate electric strike, or magnet locks with up 

to 30 VDC and 1A. 

Figure 3: EX-H22 

 

Figure 4: EX-M22 

 

2.

 

Technical Specifications 

2.1

 

Electrical Characteristics 

Input Voltage 

8–30 VDC 

Switch Voltage 

30 VDC [OC] 

Maximum Switch Current 

1 A 

Sense Range (EX-x22) 

5 to 20 cm 

Sensitivity (EX-X04) 

0.5 kg 

LED Indicator 

Red/green LED 

2.2

 

Environmental Characteristics 

Operating Environment 

Outdoor use

 

Operating Temperature Range 

-

10˚C to 50˚C (14˚F to 1

22

˚F)

 

Storage Temperature Range 

-

20˚C to 60˚C (

-4

˚F to 

140

˚F)

 

Operating Humidity 

10% to 90% 

2.3

 

5B

Physical Characteristics 

Dimensions (W x H x D) 

H: 

114 x 70 x 10 mm (4.49 x 2.76 x 0.39 in.)

 

M: 92 x 92 x 10 mm (

3.62

 x 

3.62

 x 0.39 in.) 

Weight 

H: 

50 g (1.76 oz)

 

M: 55 g (1.94 oz) 

 

3.

 

2B

Installation 

3.1

 

6B

Operation Modes 

The switches have two operation modes as determined by the brown 

wire: 

 

Brown wire not connected – Momentary mode activates the 
output [OC] for 1 second 

 

Brown wire connected to GND – Toggle mode activates the output 

[OC] ON and OFF

 

 

The green wire sets the LED to the initial green color. 

3.2

 

7B

Wiring Information 

The switches are wired using a five-wire pigtail as described in Table 1: 

Table 1: Wiring 

Red 

+Vin 

Black 

Ground (-Vin) 

Brown 

Mode setting 

Green 

LED setting 

Yellow 

Switch output (OC) 

To wire the unit: 
1.

 

Connect the power supply to the black and red wires.  

2.

 

Connect the yellow wire to the REX input in the access control 
panel or directly to the lock. 

3.3

 

8B

Installing the Switch 

When selecting the installation area, select a flat wall close to the door 

or item that the switch will control. Ensure that there are no iron 

beams, door frames, or other obstructions that may prevent insertion 
of the inlay in the wall. 
To install the switch: 
1.

 

Mark the dimensions of the inlay on the wall. 

2.

 

Mark two holes for the screws and a hole approximately in the 

middle of the plate to insert the wires.  

3.

 

Drill the three holes. 

4.

 

Mount the unit and tighten the screws. 

Figure 5: Wall Mount 

Figure 6: MP-06 Mount 

 

 

 

Отзывы: