Rosslare AYC-E 5 Series Скачать руководство пользователя страница 49

Страница: 49 / 65

Controller Operation

AYC-Ex5/T65 Series Installation and Programming Manual

Construct a code using the following

instructions:

Second digit

Set the number of wrong code attempts, which causes a

Lockout between 0 and 9 attempts.

Third and fourth digits

Sets the Duration of the lockout, between 00 and 99; the

value is multiplied by ten, resulting in 0 to 990 seconds.

4.9.11

Setting the Backlight Behavior

The controller allows you to define the way the unit’s backlight

works.

To set the backlight behavior:

Enter Programming mode.

Press

to enter Menu 6.

The left LED flashes green.

Enter one of the following codes:

5000

– Backlight off

5100

– Backlight on (default)

5200

– Backlight is off, activates for 10 seconds when a key is

pressed, after which it dims until off

5300

– Backlight is dimmed, activates for 10 seconds when a

key is pressed, after which it returns to a dimmed level

Green

Green Green

Содержание AYC-E 5 Series


































































Результаты поиска

Содержание AYC-E 5 Series

Отзывы:

Похожие инструкции для AYC-E 5 Series

Бренды по названию

Популярные бренды

Rosslare AYC-E 5 Series, Инструкция по установке и программированию

Результаты поиска

Содержание AYC-E 5 Series

Отзывы:

Похожие инструкции для AYC-E 5 Series

Бренды по названию

Популярные бренды