Ross Ultrix Acuity Скачать руководство пользователя страница 29

Страница: 29 / 115

Select ME 1 and s source on the background

bus of ME 2. Notice that ME 1 is not being

used as the background of ME 2.

Configurable Program Outputs (MultiFeed)

Each ME can have multiple program and

preview outputs that can be configured to

include only select keys or replace the

background and preset buses with the utility

buses.

Figure 3: Configurable Program Output Example

Including or excluding a key from a program

output does not change the on-air status of the

key, only whether the key is included in a

particular output when the key is on-air. The

key must still be transitioned on or off-air from

the transitions area.

To Configure a Program Output

Press the

SEL

button for the ME that you

want to configure an output for and press

Program Assignment

Select the keys that you want included in

each output for the ME.

Note:

The output must be set to FlexiMode from the

Installation menu or the key selection buttons will be gray.

Select the buses to use for the background

of each output.
•

Bkgd/Pst

— sources selected on the

background and preset buses of the ME

are used.

•

U1/U2

— sources selected on utility bus

1 and utility bus 2 of the ME are used.

Switcher Reset and Shutdown

The entire switcher or just an ME can be

restarted or reset from the control panel. This

is useful if they switcher is in an unfamiliar

state, or you are troubleshooting an issue.
• Switcher Shutdown — closes the switcher

application and prepares the control panel

and frame to be powered off.

• Switcher Restart — physically powers down

the frame and re-starts it

• ME Reset (ALL+ALL) — defaults the state of

an ME, or all MEs

To Shutdown the Switcher

Press

HOME

More

System Shutdown

Press

Shut Down

The switcher will prompt you to confirm the

restart. Once confirmed, the switcher

powers down.

Toggle the power switches in the frame and

control panel to Off.
Refer to the QuickStart poster that came

with your switcher for the locations of

power switches in control panel and frame.

To Restart the Switcher

Note:

The control panel will not start up properly if there is a

USB drive in the USB port on the control panel. You must remove

the USB drive from the USB port on the control panel before

powering the control panel up.

Press

HOME

More

System Shutdown

Press

Restart

The switcher will prompt you to confirm the

restart. Once confirmed, the frame and

control panels will power down and boot

up again.

ME Reset (ALL+ALL)

Each ME can be reset to return it to the default

state. The ME can be reset from the Global

Memory module, or the Effects Memory module.

Ultrix Acuity Operation Manual (v10.1) — Switcher Basics • 29

Содержание Ultrix Acuity




















































































































Результаты поиска

Содержание Ultrix Acuity

Отзывы:

Ross Ultrix Acuity, Руководство по эксплуатации, Страница: 29 / 115

Результаты поиска

Содержание Ultrix Acuity

Отзывы: