Ross TES9 Скачать руководство пользователя страница 18

Страница: 18 / 68

3–2 • Encoder Configuration

TES9 Software User Manual (Iss. 04)

Installing the Setup Software

The configuration program, TES9Set, is supplied with the TES9 on a CD-ROM.

To install TES9Set on the computer's hard drive

Place the TES9Set disk in the CDROM drive.

If the setup program does not start automatically:

• Go to the

Start

menu in and select

Computer

• Double-click the Compact Disk drive you inserted theTES9Set disk into.
• Double-click

Autorun.EXE

Click

Install TES9Setup Software

and follow the on-screen instructions.

Configuring the Encoder

There are three steps involved in configuring the encoder:

Connect the computer to the encoder through

Port A

or the modem or LAN jack. Refer

to the

TES9 Hardware Manual

for details.

Put the encoder into Setup mode (this is not necessary for the LAN encoder if its IP
address has already been set up). Refer to the section “

Configuring the Encoder for

Setup Mode

” on page 3-3 for details.

Run TES9Set as outlined the section “

Starting TES9Set

” on page 3-4.

Содержание TES9





































































Результаты поиска

Содержание TES9

Отзывы:

Бренды по названию

Популярные бренды

Ross TES9, Руководство пользователя программного обеспечения

Результаты поиска

Содержание TES9

Отзывы:

Бренды по названию

Популярные бренды