manualshive.com logo in svg

Ross TES9, Руководство пользователя программного обеспечения

Поделиться
Скачать
Ross TES9 Скачать руководство пользователя страница 16

2–2 • Installation

TES9 Software User Manual (Iss. 04)

Installation

The procedure for installing the TES9 is as follows:

1.

Install and connect the TES9 chassis, following the procedure described in the 

TES9 

Hardware Manual

.

2.

It is advisable to make all your connections to the TES9 rear panel with the power off.

3.

Once you have made all necessary connections, you can turn the power on.

TES9 as an Encoder

If you plan to use the TES9 as an encoder, proceed as follows:

1.

Connect the equipment providing the video signal source to the 

PROGRAM 1 IN

 

connector on the encoder.

2.

Connect the 

PROGRAM 1 OUT

 connector on the encoder to the equipment that is to 

receive the video signal with the inserted VANC data.

3.

If using a serial data connection, connect the transmit computer(s) to the serial port(s) on 
the encoder using a null modem cable (a null modem cable is shipped with the encoder). 
Alternatively, connect the transmit computer to the LAN connector on the encoder via 
an Ethernet LAN, using a standard RJ45 cable.

TES9 as a Receiver

When using the TES9 as a receiver, proceed as follows:

1.

Connect the equipment providing the video signal containing the VANC data to be 
received to the 

PROGRAM 1 IN

 connector on the encoder.

2.

Connect the TES9's 

PROGRAM 1 OUT 

connector to other equipment that needs this 

video signal; if there is none, connect a 75 ohm termination to 

PROGRAM 1 OUT

. 

3.

If using a serial data connection, connect the receive computer(s) to the serial port(s) on 
the encoder using the supplied null modem cable. Alternatively, connect the receive 
computer to the LAN connector on the encoder via an Ethernet LAN, using a standard 
RJ45 cable.

4.

If your TES9 is equipped with a second program video channel and you plan to use it, 
follow the procedure described above for the Program 1 channel, connecting to 

PROGRAM 2 IN

 and 

OUT

 instead of 

PROGRAM 1 IN

 and 

OUT

.

Note

 — For proper operation, it is essential that the output be terminated in 75ohms.

Содержание TES9





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды