Synergy Series Operation Guide (v18)
Keying • 7–17
•
(Synergy 3 and 4) Press
MLE 2 KEY 1
to assign the group to control keys, borders,
and masks in
MLE 2
’s
Key 1
group. The button will also light
automatically
if any
button is pressed in
MLE 2
’s
Key 1
group.
•
(Synergy 3 and 4) Press
MLE 2 KEY 2
to assign the group to control keys, borders,
and masks in
MLE 2
’s
Key 2
group. The button will also light
automatically
if any
button is pressed in
MLE 2
’s
Key 2
group.
•
(Synergy 3 and 4) Press
MLE 3 KEY 1
to assign the group to control keys, borders,
and masks in
MLE 3
’s
Key 1
group. The button will also light
automatically
if any
button is pressed in
MLE 3
’s
Key 1
group. On the Synergy 3, this button controls
the
DSK 1
group.
•
(Synergy 3 and 4) Press
MLE 3 KEY 2
to assign the group to control keys, borders,
and masks in
MLE 3
’s
Key 2
group. The button will also light
automatically
if any
button is pressed in
MLE 3
’s
Key 2
group. On the Synergy 3, this button controls
the
DSK 2
group.
•
(Synergy 2) Press
DSK 1
to assign the group to control keys, borders, and masks in
the
DSK 1
group. The button lights
automatically
if any button in
DSK 1
is pressed.
•
(Synergy 4) Press
MLE 4 KEY 1
to assign the group to control keys, borders, and
masks in
MLE 4
’s
DSK 1
group. The button will also light
automatically
if any
button is pressed in
MLE 4
’s
DSK 1
group.
•
(Synergy 2) Press
DSK 2
to assign the group to control keys, borders, and masks in
the
DSK 2
group. The button will also light
automatically
if any button in
DSK 2
is
pressed.
•
(Synergy 4) Press
MLE 4 KEY 2
to assign the group to control keys, borders, and
masks in
MLE 4
’s
DSK 2
group. The button will also light
automatically
if any
button is pressed in
MLE 4
’s
DSK 2
group.
2. Mask Section
(All switchers) The controls in the
Mask Section
allow you to eliminate unwanted
portions of a key signal, similar to a DVE’s crop function. The section is activated by the
MASK
button in each key group. All types of keys (except Preset Patterns) can be
masked. Each key has its own individual mask that is stored in memory.
When the
MASK
button is lit, the controls are active. If the button is turned off, the
controls are disabled and any mask that was previously applied is removed from the key.
If the
MASK
button is re-enabled for that key, the previous mask is recalled from
memory and re-applied.
•
Rotate the
TOP
knob to trim (eliminate) the top edge of the key.
•
Rotate the
BOTTOM
knob to trim the bottom edge of the key.
MLE2
KEY1
MLE2
KEY2
MLE3
KEY1
MLE3
KEY2
DSK
1
MLE4
KEY1
DSK
2
MLE4
KEY2
TOP
Original Key
Top Mask Applied
BOTTOM
Original Key
Bottom Mask Applied
Содержание SYNERGY 4000DR-003
