background image

4

• 

DO NOT operate a chain saw with one hand! Serious injury to the operator, helpers, by-

standers, etc may result from  one handed operation. A chain saw is intended for two 

handed use.

• 

DO NOT operate a chain saw when you are fatigued. 

• 

Use safety footwear, snug-fitting clothing, protective gloves, and eye, hearing and head 

protection equipment.

• 

Use caution when handling fuel. Move the chain saw at least 10 feet (3m) 

from the fuelling point before starting the engine.

• 

DO NOT allow other persons to be near when starting or cutting with the chain saw. Keep 

bystanders and animals out of the work area.

• 

DO NOT start cutting until you have a clear work area, secure footing, and a planned retreat 

path from the falling tree.

• 

Keep all parts of your body away from the saw chain when the engine is running.

• 

Before you start the engine, make sure that the saw chain is not contacting anything.

• 

Carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and 

the muffler away from your body.

• 

DO NOT operate a chain saw that is damaged, improperly adjusted, or not completely and 

securely assembled. Be sure that the saw chain stops moving when the throttle control 

trigger is released.

• 

Shut off the engine before setting the chain saw down.

• 

Use extreme caution when cutting small size brush and saplings because slender material 

may catch in the saw chain and be whipped toward you or pull you off balance.

• 

When cutting a limb that is under tension, be alert for spring back so that you will not be 

struck when the tension in the wood fibres is released.

• 

Keep the handles dry, clean, and free of oil or fuel mixture.

• 

Operate the chain saw only in well-ventilated areas.

• 

DO NOT operate a chain saw in a tree unless you have been specifically  trained to do so.

• 

All chain saw service, other than the items listed in the user manual safety and mainte-

nance instructions, should be performed by competent chain saw service personnel.

• 

When transporting your chain saw, use the appropriate guide bar scabbard.

• 

DO NOT operate your chain saw near or around flammable liquids or gases whether in or 

out of doors. An explosion and/or fire may result.

• 

DO NOT lubricate, fill with fuel or oil when the chain saw engine is running.

• 

USE THE RIGHT TOOL: Cut wood only. Do not use the chain saw for purposes for which it 

was not intended. For example, do not use the chain saw for cutting plastic, masonry, or 

building materials.

General Safety Cont ...

Содержание ROSSGARDEN RGCS45CC





















Отзывы: