background image

3

WHEN 

using the equipment, a few safety precautions must be observed to avoid 

injuries and damage to the saw.

READ 

the operating instructions carefully and comply with them at all times. 

KEEP 

this manual in a safe place, so that the information is readily available at all times.

IF 

you give the equipment to another person, It is important for them to read the operating 

instructions prior to use.

GENERAL SAFETY

Explanation of the symbols and warning signs on the machine

READ 

the user manual before using the machine.

 

ALWAYS 

wear safety goggles to guard your eyes from flying  

materials/objects and a sound-proof helmet, ear plugs or the like to protect 

your hearing.  

Wear a safety helmet if there is a risk of objects falling on you from above. 

WEAR 

gloves to protect your hands.

 

WEAR 

safety shoes to protect your feet. 

 

WARNING! 

Danger! 

 

 

DO 

not operate a chain saw with one hand!

BE 

aware of the of kickback!

MAKE 

sure that the chain brake is released. Pull 

back the handle/chain brake before operating

WHEN 

using the equipment, a few safety precautions must be observed to avoid 

injuries and damage to the saw.

READ 

the operating instructions carefully and comply with them at all times. 

KEEP 

this manual in a safe place, so that the information is readily available at all times.

IF 

you give the equipment to another person, It is important for them to read the operating 

instructions prior to use.

Содержание ROSSGARDEN RGCS45CC





















Отзывы: