Ross openGear GPI-100 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 42

Ross openGear GPI-100 Скачать руководство пользователя страница 35

GPI-100 User Manual (Iss. 06)

Configuration • 4–7

Monitoring

The GPI-100 has several alarms that can affect the overall status of the card. This section outlines
the three status tabs for the GPI-100. These Status tabs provide read-only information to help
monitor the GPI-100 via DashBoard. The indicators in the Status tabs can vary in severity from
green (valid) to red (alarm). DashBoard reports the most severe alarm for a single field.

Product Status

The

Product

tab provides read-only information, such as board revision, serial number, and rear

module type. This information is helpful to a Ross Video technical support when there are
questions about the operation of the unit.

Example of a Product Status Tab

GPIO Status Tab

The

GPIO Status

tab reports the status of the eight GPIO inputs/outputs. The status of each of

the inputs/outputs is either Open or Closed where Open means logic level 1 (3.3V) and Closed
means logic level 0 (0V).

Example of a GPIO Status Tab

«
...
33
34
35
36
37
...
»

Содержание openGear GPI-100











































Отзывы:

Нет отзывов